:00Thu 24 Sep

Put reels in

How a put-in works

Scan the reel, then push it into any empty bay. Nothing is lit: the sensor says where it went, and Janus records it there.

Scanner ready
Later · not in R1Neo J01-Q12; scan-resolution

Scanning every barcode on a label and resolving codes that disagree.

Not in R1
One scan names the reel in Neo R1; multi-label merge is not required initially.
R1 instead
One scan of the label; a label no format reads, or reads two ways, is answered as such. Open Put in
  1. Scanned, done14:32
  2. Codes disagree, needs review5 000 vs 4 000 pcs
  3. Any free bay, not yet
  4. Sensor saw it, not yet, sensor-confirmed
  5. Stored, not yet

Step 2 of 5 · Codes disagree · 5 000 vs 4 000 pcs · needs review

What the steps mean

A square step is recorded by Janus. A round step is confirmed by the rack’s sensor at the bay.

Two barcodes disagree about this reel.

Safe: nothing is recorded and no bay lights until one scan is removed.

Same part, different quantity. Check the quantity printed on the label. Remove the scan that doesn't match.

MH10 barcode

R-2026-0042

Quantity
5 000 pcs
Part
PN-0603-10K

Keep if the label shows 5 000.

GS1 barcode

(10)LOT-2614-042

Quantity
4 000 pcs
Part
PN-0603-10K

Keep if the label shows 4 000.

Neither matches the label:

SR-01 · Reel rack A

SMT Line 2 · position 1 · 42 empty bays

Online
Tier 3 · bays 9–20front view

10 empty

Bay light
Off · nothing to do here. Off · nothing to do
Sensor at L14
Empty
Fits
7″ reel · 8 mm tape · 1 bay
Tower lights
Yellow tower · attention on this rack. Left yellow · Off · nothing to do here. Right off

Not finished

1 put-in not finished
  • R-2026-0109 · PN-SMAJ24A
    2 500 pcs from label · The sensor did not see it at SR-01-T4-L31 · covers WO-260714-09's 480 pcs short
    Waiting for sensor
    You12 min ago
3 more in the Review queue
  • R-2026-0118 · PN-0402-100N
    4 000 pcs · default quantity · Started at Station SMT-1, not finished
    Needs review
    Gábor NagyOperator · 1 h 4 min ago
  • R-2026-0121 · PN-QFN32-MCU7
    600 pcs from MES · Sent by MES, waiting for review
    Not put in yet
    MES adapterConnected system · 2 h ago
  • R-2025-0913 · PN-0603-10K
    Quantity unknown · no scan or sensor has seen this reel
    Record, no reel
    Old record · before Janus

Alerts

Faults and blocked work stay here until fixed. Notices can be cleared.

SR-02 is limited

Bence Tóth is on itsince 09:41 · 4 h 51 min14:30 installation map v4 drafted by Dávid Horváth under permit · waiting to be applied

Tier 3, bays 1–16 are Unknown. Blocks 2 take-outs for WO-260714-09 and hides 310 pcs of PN-QFN32-MCU7. The rest of SR-02 works.

Troubleshoot SR-02Stays until fixed

Label not recognised

A Würth Elektronik label matched no code rule.

Put-in not finished

Reel R-2026-0109 is waiting for the sensor at SR-01-T4-L31: finish putting it in, or cancel.

Counter ReelSave is failing

Owner: line counter vendorsince 13:48

12 messages waiting. SMT Line 2 counters don't know about reels taken out since 13:48.

Snapshot taken · 14:30

Verified · off-host copy 14:30. Snapshots every 15 min while Janus is busy.

Choose working rack

Scans and bay lights on this station use the working rack. Opening another rack never switches it.

Racks

Help

What the words mean

Language

Applies to this station only. Records keep the words they were written in.

Enter quantity

The quantity printed on R-2026-0042, or your count. It replaces Unknown as its first quantity: no approval, no variance.

Whole pcs.

Discard this scan?

R-2026-0042 will not be recorded. Scan it again to put it in.

Prototype

Put in

Preview stateCodes disagree

Simulate

View as

This page

Purpose
Put reels in by evidence: scan, the bay lights, the sensor confirms.
Release
R1
First viewport
1 primary · 1 notice · 3 blocks