:00Thu 24 Sep

Dávid Horváth, Danutek technician account

Always on while R1 is trialled. Every action is logged under this named account; it is not a site user.

Rack setup

Not searching · no rack network approved

Later · not in R1Neo 0018 · 0032 §16

Approving the rack network in Janus: which network port serves the racks, its subnet and address pool

Not in R1
Janus never changes host networking: the Janus Service CLI designates rack ports, applies their address plan and verifies it; Janus only checks
R1 instead
Rack port requirement checks, read-only, with the Service CLI step that fixes an unmet one Open Rack setup

How rack setup works

Each new controller found on the rack port is set up in eight steps, one at a time. Janus reads the rack port’s checks from the host; it never changes this computer’s network.

  1. IdentifyTiers light in turn, then the rack flashes twice.
  2. NameRack ID and name. Its rack label follows the ID.
  3. Where it isScan the floor label.
  4. AddressOff the factory default.
  5. ShapeSides, tiers, bays. Towers are read from the rack.
  6. BaselineEvery board replies; every bay is read. Full racks too.
  7. Follow the lightSomeone at the rack puts a reel where each sampled bay lights.
  8. Put in serviceOnly when the rack qualifies as a whole. Rack labels print.
Before you power on1 of 8 checked by Janus · rack network not approved · 6 at the rack
  1. Your accessValid · checked by JanusDanutek technician account · service visit until Sun 28 Sep 18:00. A setup left paused then passes to Eszter Szabó, who sponsors the visit.
  2. Rack portNot approved · checked by Janusen5 on janus-smt-line2 is connected, not approved. Ask Eszter Szabó below.
  3. ControllerAt the rackCable it to the rack switch, a free port P9–P23. Power one new controller at a time: each one arrives on 192.168.0.10.
  4. Your laptop and phonePhone paired · 14:19On the office network or Line 2 Wi-Fi, never the rack switch: the rack network doesn’t serve Janus. Open https://janus-smt-line2.local:8443.
    Pair another phone
    Scan with the phone camera. Questions only a person at the rack can answer go to it.
  5. The rackAt the rackEmpty or already full: nothing needs clearing. The baseline reads what is in it, and each reel is scanned in after the rack is in service. Keep the firmware as delivered; a change stops Put in service.
  6. Someone at the rackAt the rackFollow the light needs a named person there: they put a reel where each bay lights and look at the tower.
  7. Floor labelAt the rackThe position has a floor label, e.g. POS-L2-03. Where it is is set by scanning it. Missing labels print from Label printer SMT-2.
  8. Which way roundAt the rackT4T3T2T1T4T3T2T1Side A faces the aisle. Tier 1 is at the bottom. Bay 1 is at the left as you face each side.

Not searching: no rack network is approved on this computer

Network port en5 on janus-smt-line2 is connected but not approved

Approve Rack network · en5 to find controllers

Janus searches only approved networks.

Janus may

  • Yes: Search for controllers on en5
  • Yes: Connect, view only, to identify them

Janus never

  • No: Changes a controller address without a second approval
  • No: Adds a rack without your setup and checks

This needs the right Approve rack network.

Eszter Szabó (site administrator) can approve it.

Open Connections

Alerts

Faults and blocked work stay here until fixed. Notices can be cleared.

SR-02 is limited

Bence Tóth is on itsince 09:41 · 4 h 51 min14:30 installation map v4 drafted by Dávid Horváth under permit · waiting to be applied

Tier 3, bays 1–16 are Unknown. Blocks 2 take-outs for WO-260714-09 and hides 310 pcs of PN-QFN32-MCU7. The rest of SR-02 works.

Troubleshoot SR-02Stays until fixed

Label not recognised

A Würth Elektronik label matched no code rule.

Eszter Szabó is told. Put the reel aside.

Put-in not finished

Reel R-2026-0109 is waiting for the sensor at SR-01-T4-L31: finish putting it in, or cancel.

Márta Kovács is on it.

Counter ReelSave is failing

Owner: line counter vendorsince 13:48

12 messages waiting. SMT Line 2 counters don't know about reels taken out since 13:48.

Handled by the site administrator.

Snapshot taken · 14:30

Verified · off-host copy 14:30. Snapshots every 15 min while Janus is busy.

Help

What the words mean

Language

Applies to this station only. Records keep the words they were written in.

Nothing found? Troubleshoot

Network ports on janus-smt-line2, read from the host. The Janus Service CLI decides which is a rack port; Janus never changes them.

Searching

  • Rack port 1 · en5
    192.168.0.253/24 · set by the Janus Service CLI · requirements met
    Searching

Not searching

  • Office network · en0
    Not a rack port.
    Not searched
  • Wi-Fi · en1
    Not used for racks.
    Skipped
Other network ports12
  • utun3 · virtual or tunnel port
  • lo0 · this computer only
  • bridge100 · not connected right now
  • 9 more with the same reasons

Deep search

Racks in service may pause for up to 2 s.

Two replies claim serial 202505012000177

Identify each reply, then type the MAC from the device label.

Reply A

MAC
28:3D:E8:F0:A8:72
Address
192.168.0.51:502
Firmware
V2.01-2503
Heard
4 s ago

Reply B

MAC
28:3D:E8:F0:A8:73
Address
192.168.0.52:502
Firmware
V2.01-2503
Heard
9 s ago

Prototype

Rack setup

Preview stateRack network approved in Janus

Later · not in R1

View as

This page

Purpose
New controllers found, and the next step for each.
Release
R1
First viewport
1 primary · 1 notice · 3 blocks